6 months ago - In EIGRP enabled router which command is used to display the bandwidth of an interface?
6 months ago - Which among the listed below is the global configuration command is used to enable Rapid PVST+?
6 months ago - During the troubleshooting of networks why would a network engineer do the show cdp neighbor command on a router?
6 months ago - What port state among the listed below will switch ports immediately transition to when configured for PortFast?
6 months ago - The CCIE of RS Telecom Inc has changed the router ID on a router that is working in an OSPFv2 environment. What should the administrator do to reset the adjacencies and use the new router ID?
6 months ago - A visitor of RMS Missile facility connects wirelessly to the company network using a cell phone. The visitor then configures the cell phone to act as a wireless access point that will allow other visitor to connect to the company network. Which type of security threat best describes this situation?
6 months ago - How many paths can the EIGRP routing process use to forward packets from RMSRouter to a neighbor router?
6 months ago - Which command listed below is used to verify that OSPF is enabled and also provides a list of the networks that are being advertised by the network?
6 months ago - In the Cisco Enterprise Architecture, what module consists of the entire campus infrastructure, to include the access, distribution, and core layers?
6 months ago - Which LACP mode places a port in an active negotiating state, in this state, the port initiates negotiations with other ports by sending LACP packets?
6 months ago - Among the listed ip route commands below which one pertains to propagating a default route?
6 months ago - In Chapter 6, what OSPF LSA type is used to inform routers of the router ID of the DR in each multiaccess network in an OSPF area?
6 months ago - In the study of scaling networks, what is the purpose of using protocol-dependent modules in EIGRP?
6 months ago - In the discussion of EIGRP which table is used by EIGRP to store all routing information that are learned from EIGRP neighbors. Choose 1 letter only?
6 months ago - What command that control the degree to which EIGRP performs load balancing?
6 months ago - Which feature of EIGRP enables administrators to create summary routes anywhere within the network rather than rely on the traditional distance vector approach of performing classful route summarization only at major network boundaries?
6 months ago - "show ip eigrp neighbors" is the command that should be issued on a router to verify that eigrp neighbors or known eigrp adjacencies were formed.
6 months ago - Two routers R1 and R2 share a 128kbps link. The network specialist of the company wants to limit the bandwidth used by eigrp between these two routers to 64kbps. Which command is used on both routers to configure the new bandwidth setting?
6 months ago - Routers R2, R3, and R4 above are correctly configured. Why did R1 not establish an adjacency with R2, R3 and R4?
6 months ago - In the scenario of upgrading the Cisco IOS image on a 2921 ISR router of ABC Telecoms. What command could the engineer use to verify the total amount of flash memory as well as how much flash memory is currently available?
6 months ago - What command displays the number of packets sent and received ? Question 10Select one: a. Sh ip protocol b. Sh ip eigrp packets c. Sh ip route d. Sh ip eigrp traffic
6 months ago - In EIGRP operation which command is used to display the bandwidth of an interface on an EIGRP-enabled router?
6 months ago - In the scenario of router configuration which IOS CLI mode listed below must a network administrator issue the bandwidth command to configure the specific value for the bandwidth?
6 months ago - What show command that should be issued on a router to verify that eigrp adjacencies were formed. This is commonly use in eigrp network troubleshooting in finding connected networks that uses eigrp protocol?
6 months ago - In a scenario of network troubleshooting will the use of EIGRP automatic summarization cause inconsistent routing in a network?
6 months ago - Refer to the figure above. Which command should be used to configure EIGRP to only advertise the network that is attached to the gigabit Ethernet 0/1 interface?